Wave Jib Manuals
_#38999001 WAVE JIB KIT_ PAGE 1 of 2 2) With trampoline loosened, force hulls 1) Install bow spreader tangs on each apart and place bow spreader in bow under existing bridle wire tang as position on pins installed on bows shown. Pin faces towards center. 3) With swivel cleat mounted to plate, install jib sheet jam 4) cleat plate under existing Install jib halyard trampoline hook* as shown. This is block on pig tail installed under center of three tramp and place pigtail on hooks. Use the upper two of four holes shroud shackle in the plate. _(*F...


View the Manual
Buoyancy Compensator Manuals
_EVERYTHING FOR THE PERFECT DIVE..._ Buoyancy Compensator Owner’s Manual DOCUMENT OUTLINE * xs_scuba_bc_manual.pdf * Front Cover * Warning / Disclaimer * Defintions * Table of Contents * General Precautions & Warnings * Introduction * Intended Use & Function * Standard Features * Overview of Standard Features & Adjustments * Valves * Power Inflator * Overpressure Relief Valve * Primary Adjustment Points * Shoulder Straps * Cummerbund Waistband * Cylinder Band with Buckle * Tank Locator Strap * Sternum Strap * Integrated Weight Systems * Releasa...


View the Manual
Sahara 4505-1 Manuals
3 OPTIONAL MATERIALS ® • 1/2"thick marine plywood block (slightly larger than pump base). • Waterproof adhesive (epoxy, silicone adhesive, or fiberglass SAHARA SERIES AUTOMATIC resin) to mount block. • 16gauge wire (brown and black). BILGE PUMPS PUMP MOUNTING INSTRUCTIONS 4505 / 4507 / 4511 INSTALLATION INSTRUCTIONS WARNING: Remove the pump mounting base (See Figure 3). Remove the foam block that supports the float during shipping. SAVE THESE INSTRUCTIONS Failure to do this prevents the pump from starting when water Form Number 69370 Rev. C 031...


View the Manual
Sahara 4505-7 Manuals
3 OPTIONAL MATERIALS ® • 1/2"thick marine plywood block (slightly larger than pump base). • Waterproof adhesive (epoxy, silicone adhesive, or fiberglass SAHARA SERIES AUTOMATIC resin) to mount block. • 16gauge wire (brown and black). BILGE PUMPS PUMP MOUNTING INSTRUCTIONS 4505 / 4507 / 4511 INSTALLATION INSTRUCTIONS WARNING: Remove the pump mounting base (See Figure 3). Remove the foam block that supports the float during shipping. SAVE THESE INSTRUCTIONS Failure to do this prevents the pump from starting when water Form Number 69370 Rev. C 031...


View the Manual
Sahara 4505MP1 Manuals
3 OPTIONAL MATERIALS ® • 1/2"thick marine plywood block (slightly larger than pump base). • Waterproof adhesive (epoxy, silicone adhesive, or fiberglass SAHARA SERIES AUTOMATIC resin) to mount block. • 16gauge wire (brown and black). BILGE PUMPS PUMP MOUNTING INSTRUCTIONS 4505 / 4507 / 4511 INSTALLATION INSTRUCTIONS WARNING: Remove the pump mounting base (See Figure 3). Remove the foam block that supports the float during shipping. SAVE THESE INSTRUCTIONS Failure to do this prevents the pump from starting when water Form Number 69370 Rev. C 031...


View the Manual
Sahara 69370 Manuals
3 OPTIONAL MATERIALS ® • 1/2"thick marine plywood block (slightly larger than pump base). • Waterproof adhesive (epoxy, silicone adhesive, or fiberglass SAHARA SERIES AUTOMATIC resin) to mount block. • 16gauge wire (brown and black). BILGE PUMPS PUMP MOUNTING INSTRUCTIONS 4505 / 4507 / 4511 INSTALLATION INSTRUCTIONS WARNING: Remove the pump mounting base (See Figure 3). Remove the foam block that supports the float during shipping. SAVE THESE INSTRUCTIONS Failure to do this prevents the pump from starting when water Form Number 69370 Rev. C 031...


View the Manual

Designated trademarks and brands are the property of their respective owners | Disclaimer