Mirage Rudder Manuals
STEERING AND CONTROL LINE REPLACEMENT KIT INSTRUCTIONS FOR MIRAGE OR TANDEM MIRAGE Kit Contents. 2 steering control lines and tube assemblies, (labeled) 1 up control line and tube assembly, (shortest, without swedged loop) 1 down control line and tube assembly. (Has loops swedged on both ends) Two 3/16 inch shock cord loops for up/down line to arm. Four Zip ties Two linking loops Tools Required 1/8th inch Allen wrench Screw drivers Knife or side cutters THIS KIT IS INTENDED… to replace the rudder control lines when the original lines wear out. ...


View the Manual
Mirage Inflatables Manuals
Congratulations on purchasing the Hobie Sail Kit for the Hobie inflatable kayaks. Follow these simple instructions and you’ll be out and sailing in minutes. K A Y A K I N G Step 1: Connect mast sections together. Thinner Step 6: Attach sail stays to kayak and diameter section adjust tension. Start with side shrouds by is mast top. attaching them to each side of the kayak securing stay hooks to each stainless ring. Tension stopper knots until mast is straight. Step 5: Insert mast Finish by attaching the forstay to the bow Step 3: Insert batten S...


View the Manual
MAST FLOAT Manuals
# 30113 Page 1 of 1 #30113 MAST FLOAT 1) Assemble all parts onto shaft. 2) Place lower end of shaft against mast. 3) PVC pipe keeps the float above the masthead. For 17, 18, 20 & 21 installation... trim to 2”. 4) Drills needed: 15/64” when using caps. 3/16” for rivets only. NOTE: Bearing must be placed open side towards center of float. H14 / H16 H17 / H18 / H20 / H21 Position as shown. Be sure Float has complete 360 degree rotation. Drill mast and rivet single (long rivet with cap) to hold location. Bend eye straps to conform to your mast curv...


View the Manual
Spinnaker Snuffer Manuals
Composite Retriever Assembly Manual 1. (only in case of adaptation on a standard pole) Remove the center pole support wires from the spinna ker pole. Do this by either cutting the wire or drilling the head off the rivet, which fixes the padeye. (seulement dans le cas d’adaptation sur un tangon stan dard) Retirer les câbles de support placés au centre du tan gon. Pour cela, vous pouvez soit couper les câbles ou faire sauter la tête du rivet qui fixe le pontet en perçant dedans. 2. Slide on to the spinnaker pole from the front cross beam end the ...


View the Manual
Sail Adapter Manuals
Congratulations on purchasing the Step 3: Slide down haul Tandem Mirage Sail Adapter Kit. hook up the bottom of the Follow these simple installation mast approximately 10 instructions and you'll be out on the inches,then tighten screw Tandem Mirage water in no time. to secure the hook. Once tightened,stretch smaller Sail Adapter bungee at base of sail onto the down haul hook. adapter and Step 1: Flip up Step 4: Slide mast into front seat of kayak adapter. Sail and insert adapter 1543 into scupper. Step 5: Run the main sheet from the sail side,t...


View the Manual
Twist-n-Seal Hatch Manuals
These instructions are intended to help guide the installation of your new Twistnseal hatches. The installation of the 8" hatch is shown here, but the same instructions apply for the 6" hatch. 1. Remove your oldstyle hatches from your boat. Be sure to keep the screws because you will be re using them to install the new hatch. Once the hatch is removed, clean any debris off the kayak surface that may have accumulated over time (sand and small rocks). You will be using the new backing ring that comes with the new hatch, so take the old ring out o...


View the Manual
Tandem Mirage Manuals
Congratulations on purchasing the Hobie Step 4: Tie in the batten (Note: Be sure that Sail Kit. Follow these simple instructions when tying, the batten is pulled snug into the sail). and you'll be out and sailing in minutes. If you are using this kit for your Tandem Mirage, ignore steps 5 and 6 shown here and consult your conversion kit manual. Feed the line through the Next, feed the line Step 1: Connect hole in batten head. through ring on the TIP: mast poles opposite side of sail and A little tape around the together. pull back snug into the...


View the Manual
V2 Drum Manuals
1 ASSEMBLING THE NEW MIRAGE DRIVE DRUMS AND CABLES CAUTION: The new cables and drums are slotted for easier maintenance and tune ups. They are not interchangeable with the older parts. WARNING: If cables are installed incorrectly, they may twist off the drums, causing the Drive to fail. TIP: DO NOT REUSE Nyloc nuts when installing new cables. The slotted cable threads have 40% less area worn Nylocs may back out causing Drive failure or adjustment problems. Tools and materials required: 7/16 inch wrench needle nose pliers Marine grade axle greas...


View the Manual

Designated trademarks and brands are the property of their respective owners | Disclaimer