2. Loosen the two screws in the clamping bracket, then place it over the windshield frame and mirror base at the selected location. (Figure 2) 3® OPTION 1 For windshield frames less than .450" thick, or a stepped frame (Figure 3), a small spacer of aluminum, plastic, or marine plywood may be used between the SKI MIRROR base and the windshield frame. 9083 OPTION 2 For windshields with a stepped frame (Figure 3), INSTALLATION INSTRUCTIONS using the mounting bracket as a template, mark the SAVE THESE INSTRUCTIONS width of the bracket on the windsh...

3 Figure 1 ® 3Way Bilge Pump Switch 7615A INSTALLATION INSTRUCTIONS Attwood marine hardware, navigational lighting, bilge pumps, and other marine accessories are specified more than any other brand by America’s bestknown boat manufacturers as original equipment. Look to Attwood for quality replacement parts and marine accessories. SAVE THESE INSTRUCTIONS Form Number 69260 Rev. B 0311 FEATURES Attwood’s 3Way Bilge Pump Switch is the perfect switch to use with Attwood automatic bilge pumps. RECOMMENDED TOOLS FOR INSTALLATION 1. Saw or drill for m...

3 Figure 1 ® 3Way Bilge Pump Switch 7615A INSTALLATION INSTRUCTIONS Attwood marine hardware, navigational lighting, bilge pumps, and other marine accessories are specified more than any other brand by America’s bestknown boat manufacturers as original equipment. Look to Attwood for quality replacement parts and marine accessories. SAVE THESE INSTRUCTIONS Form Number 69260 Rev. B 0311 FEATURES Attwood’s 3Way Bilge Pump Switch is the perfect switch to use with Attwood automatic bilge pumps. RECOMMENDED TOOLS FOR INSTALLATION 1. Saw or drill for m...

3 TO REMOVE EXISTING CARTRIDGE ® WARNING If Aerator is installed thruhull, BOAT MUST BE OUT OF THE WATER to remove or replace motor cartridge. BILGE AND AERATOR PUMP The pump, plumbing and connections may be below the water level. REPLACEMENT MOTOR CARTRIDGE Removing the cartridge while the boat is in the water may result in flooding and sinking of your boat. 1. Hold pump housing firmly. Depress motor cartridge tabs, then 4620, 4622, 4624, 4623, 4625 SERIES twist cartridge counterclockwise to remove. SAVE THESE INSTRUCTIONS Figure 1 Form Number...

3 SKI TOW INSTALLATION INSTRUCTIONS ® NOTE: Before you drill or cut a hole in your boat, BE ABSOLUTELY CERTAIN there is room for the Ski Tow and the internal 21/2" x 5" (64mm x 127mm) Backing Plate. See Figure 2. 1. Carefully mark center of the hole. STAINLESS STEEL SKI TOW 2. Use a 21/8" (54mm) hole saw to cut hole for the Ski Tow. See INSTALLATION INSTRUCTIONS Figure 2. 3. Separate fasteners and Backing Plate from the Ski Tow and set aside. Apply a small bead of marine sealant to the groove under 66448 SERIES the Ski Tow flange. Place Ski Tow...

3 POLE HOLDER INSTALLATION INSTRUCTIONS ® NOTE: Before you drill or cut a hole on your boat, BE ABSOLUTELY CERTAIN there is room for the unit to fold in beneath the deck or gunwale where it will be installed. The Pole Holder, in the down PUSH POLE HOLDER position, will be recessed beneath the deck or gunwale. 66346 1. Use template provided to mark opening in deck (Figure 1). INSTALLATION INSTRUCTIONS 2. Cut opening using sabre saw. Place a bead of marine sealant around opening (Figure 2). Attwood marine hardware, navigational lighting, bilge pu...

3 DO NOT USE PUMP TO REMOVE GASOLINE, OIL OR OTHER FLAMMABLE LIQUIDS. ® DOING SO COULD RESULT IN FIRE, EXPLOSION, AND SERIOUS PERSONAL INJURY. Always use the fuse amperage rating specified for your pump model. Failure to do so could result in serious personal injury or fire hazards. HEAVY DUTY BILGE PUMP Attwood bilge pumps are designed to exhaust standing WATER ONLY. They are not intended to prevent rapid accumulation of onboard water 4030, 4060, 4031, 4061 due to rough weather, severe storms, hull damage, and/or other unsafe navigational cond...

3 Figure 1 ® 3Way Bilge Pump Switch 7615A INSTALLATION INSTRUCTIONS Attwood marine hardware, navigational lighting, bilge pumps, and other marine accessories are specified more than any other brand by America’s bestknown boat manufacturers as original equipment. Look to Attwood for quality replacement parts and marine accessories. SAVE THESE INSTRUCTIONS Form Number 69260 Rev. B 0311 FEATURES Attwood’s 3Way Bilge Pump Switch is the perfect switch to use with Attwood automatic bilge pumps. RECOMMENDED TOOLS FOR INSTALLATION 1. Saw or drill for m...