VT 9114 Manuals


INTRODUCTION
Parts Check List:
To purchase replacement battery
1.
Handset
packs, call VTECH Communications
2.
Base Unit
at 1-800-595-9511.  In Canada, call
3.
Telephone Line Cord
VTECH Electronics at 1-800-267-
4.
Battery Pack
5.
AC Adapter
7377.
1
91-005435-020-000
IMPORTANT SAFETY INSTRUCTIONS
INSTALLING/REPLACING THE BATTERY PACK
When using your telephone equipment, basic safety precautions should always be followed
1. Slide the battery cover off by gently
to reduce the risk of fire, electric shock and injury, including the following:
pressing on the recessed area with
1. Read and understand all instructions.
a downward motion.
2. Follow all warnings and instructions marked on the product.
2. Unplug and remove the old battery
3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or
pack. Don't put the old battery pack
aerosol cleaners. Use a damp cloth for cleaning.
in a trash compactor or a fire - it
4. Do not use this product near water (for example, near a bath tub, kitchen sink, or
could burst.
swimming pool).
3. With the red and black wires at the
5. Do not place this product on an unstable cart, stand, or table. The product may fall,
bottom of the pack, angle the top of
causing serious damage to the product.
the battery into the compartment,
6. Slots and openings in the cabinet and the back or bottom are provided for ventilation. To
under the two “claws”. Next, press
protect it from overheating, these openings must not be blocked by placing the product
the lower end of the battery pack
on the bed, sofa, rug, or other similar surface.  This product should never be placed near
down, so it is held in place by the
or over a radiator or heat register. This product should not be placed in a built-in-
lower claw. Now, plug the connector
installation where proper ventilation is not provided.
into the socket, located below the
7. This product should be operated only from the type of power source indicated on the
battery. Slip the battery wires into the
marking label. If you are not sure of the type of power supply to your home, consult your
wire guide, located below and to the
dealer or local power company.
left of the socket.
8. Do not allow anything to rest on the power cord. Do not locate this product where the cord
4. Replace the battery cover by sliding
will be abused by persons walking on it.
it into place.
9. Never push objects of any kind into this product through cabinet slots, as they may
5. The new battery pack must be charged before using your telephone. Place
touch dangerous voltage points or short out parts that could result in a risk of fire or
the handset in the cradle of the base unit to allow it to charge for 16 hours.
electric shock. Never spill liquid of any kind on the product.
Maximum battery life between charges is more than 3.75 hours of
10.To reduce the risk of electric shock, do not disassemble this product. If service or repair
continuous talk time or 3.75 days of standby.
work is required, contact VTech Customer Service at 1-800-595-9511.  Opening or
CAUTION: To reduce the risk of fire or injury, read and follow these instructions:
removing cabinet parts other than specified access doors may expose you to dangerous
1. Use only VTECH battery pack supplied, or equivalent..
voltages or other risks. Incorrect reassembling can cause electric shock when the
2. Do not open or mutilate the battery. Released electrolyte is corrosive and
appliance is subsequently used.
may cause damage to the eyes or skin. It may be toxic if swallowed.
11.Do not overload wall outlets and extension cords as this can result in the risk of fire or
3. Exercise care in handling batteries in order not to short the battery with
electric shock.
conducting materials such as rings, bracelets, and keys.  The battery or
12.Unplug this product from the wall outlet:
conductor may overheat and cause burns.
a) When the power supply cord or plug is damaged or frayed.
4. Do not dispose of the battery in a fire. The cell may explode.
b) If liquid has been spilled into the product.
The RBRC™    Seal
c) If the product has been exposed to rain or water.
The  RBRC®  Seal on the  nickel-cadmium battery  indicates that
d) If the product does not operate normally by following the operating instructions. Adjust
VTech Communications, Inc. is voluntarily participating in an industry
only those controls that are covered by the operating instructions, because improper
program to collect and recycle these batteries at the end of their
adjustment of other controls may result in damage and will often require extensive work
useful lives, when taken out of service within the United States and
to restore the product to normal operation.
Canada.
e) If the product has been dropped and the cabinet has been damaged.
The RBRC® program provides a convenient alternative to placing used nickel-
f) If the product exhibits a distinct change in performance.
cadmium batteries into the trash or municipal waste, which may be illegal in
13.Avoid using a telephone (other than a cordless type) during an electrical storm. There
your area.
may be a remote  risk of electric shock from lightning.
VTech’s participation with RBRC® makes it easy for you to drop off the spent
14. Do not use the telephone to report a gas leak in the vicinity of the leak.
battery at local retailers participating in the RBRC® program or at authorized
VTech product service centers. Please call 1-800-8-BATTERY™ for information
SAVE THESE INSTRUCTIONS
on Ni-Cd battery recycling and disposal bans / restrictions in your area. VTech’s
involvement in this program is part of its commitment to protecting our
environment and conserving natural resources.
RBRC ®  is a registered trademark of Rechargeable Battery Recycling Corporation.
2
3
GETTING STARTED
HANDSET FEATURES
REDIAL / PAUSE KEY

When you hear the dial tone,
press  REDIAL to call the last
number dialed on your phone.

It can also be used to store the
last number dialed into the speed
dial memory. See Storing a
Redial Number into Speed Dial
for details.

You can store pauses into your
speed dial numbers. See Storing
Pauses in Memory
 for details.
ON LED
CHAN KEY

The  ON LED lights when the

Pressing the CHAN key when the
Setting Up Your VT9114
Handset is on an active call.
Handset is in use will activate a
1. Choose an area near an electrical outlet and a telephone wall jack.

It flashes in cadence with an
channel change to the next free
2. Plug the AC power adapter into an electrical outlet and the AC connector to
incoming ring.
channel.
the power jack on the bottom of the Base Unit. Insert the cord in the channel

It flashes quickly during

This is used if you are
guide.
Programming mode.
experiencing noise or
CAUTION: Use only the AC adapter shipped with your VT9114. It  is

It flashes slowly when the battery
interference on the current
specifically designed for this product.
NOTE:
Connect power to the Base Unit before placing the handset in the
pack is low.
channel.
cradle.
ON/ FLASH KEY
MEM/PROG KEY
3. CHARGE THE HANDSET BATTERY PACK BEFORE USE. The batteries

Press the ON key to make a call.

Press the MEM key to enter
recharge automatically whenever the Handset is in the Base Unit cradle.

If you are currently on a call, and
MEMORY mode.
The batteries must be charged for 16 hours before using your phone for the
you hear a call waiting tone,

The sequence for dialing out a
first time.
press ON to switch to the second
speed dial number in memory is:
4. Connect the telephone line cord. Insert one end of the telephone line cord
call. Press ON again to return to
ONMEM, Number Button (0-9).
into the phone jack on the bottom of  the Base Unit. Plug the other end into
the original call.

Press  MEM/PROG  to enter
a telephone wall jack.  Make sure the plugs snap securely into place. Insert
VOLUME  CONTROL
programming mode. See
the cord in the channel guide.

Adjust the volume of what you
Programming Speed Dial
5. CHECK FOR A DIAL TONE. After the battery pack is charged, pick up the
hear through the Handset.
Numbers for more details.
Handset and press the ON key. The IN USE LED on the Base and ON LED

While on a call, press the          or
TONE/ * KEY
on the Handset should light up, and you should hear a dial tone. If not, see
     key to adjust the listening

In PULSE dialing mode, this key
IN CASE OF DIFFICULTY.
volume. The Handset will emit a
is used to switch to Temporary
CAUTION:
double beep when the maximum
TONE dialing mode.
1. Never install telephone wiring during a lightning storm.
or minimum volume level has
2. Never install telephone jacks in wet locations unless the jack is specifically
been reached.
designed for wet locations.
3. Never touch uninsulated telephone wires or terminals unless the telephone
OFF KEY
line has been disconnected at the network interface.

Press the OFF key to exit all
4. Use caution when installing or modifying telephone lines.
modes of operation.
4
5


Big size of image:

Please install Flash player from http://get.adobe.com/flashplayer/!

42 42 51 51

Designated trademarks and brands are the property of their respective owners | Disclaimer