t2151 Manuals





















































































































































































Introduction
Parts Check List:
To purchase replacement batteries,
1.
Handset
call VTech Communications at 1-800-
2.
Base Unit
595-9511. In Canada, call VTech
3.
Telephone line cord
Telecommunications Canada Ltd. at
4.
Battery
5.
Power Adapter
1-800-267-7377.
6.
User’s Manual
1
Important Safety Instructions
Installing/Replacing the Battery
When using your telephone equipment, basic safety precautions should always be
1. Slide the battery cover off by gently
followed to reduce the risk of fire,electric shock and injury, including the following:
pressing on the recessed area with
1.
Read and understand all instructions.
a downward motion.
2.
Follow all warnings and instructions marked on the product.
2. Unplug and remove the old battery.
3.
Unplug this product from the wall outlet before cleaning. Do not use liquid or
aerosol cleaners. Use a damp cloth for cleaning.
3. With the red and black wires at the
4.
Do not use this product near water (for example, near a bath tub, kitchen sink
bottom of the battery, angle the top
or swimming pool).
of the battery into the compartment,
5.
Do not place this product on an unstable surface, such as a table, shelf or
under the claws.  Next, press the
stand. The product may fall, causing serious damage.
lower end of the battery down, so it
6.
Slots and openings in the back or bottom of the base unit and handset are
is held in place by the lower claw.
provided for ventilation. To protect them from overheating, these openings
Now, plug the connector into the
must not be blocked by placing the product on a soft surface such as a bed,
socket, located below the battery.
sofa or rug. This product should never be placed near or over a radiator or heat
register. This product should not be placed in any area where proper ventilation
Slip the battery wires into the guide,
is not provided.
located below and to the left of the
7.
This product should be operated only from the type of power source indicated
socket.
on the marking label. If you are not sure of the type of power supply in your
4. Replace the battery cover by sliding
home, consult your dealer or local power company.
it into place.
8.
Do not allow anything to rest on the power cord. Do not install this product
5. The new battery must be charged
where the cord may have anyone walking on it.
before using your telephone. Place
9.
Never push objects of any kind into this product through slots in the base or
the handset in the base unit to allow
handset as they may touch dangerous voltage points or short out parts that
it to charge for 15 hours. Maximum
could result in a risk of fire or electric shock. Never spill liquid of any kind on the
product.
battery life between charges is approximately 3.75 hours of talk time or
10. To reduce the risk of electric shock, do not disassemble this product, but take
3.75 days of standby.
it to an authorized service facility. Opening or removing parts of the base or
CAUTION: To reduce the risk of fire or injury, read and follow these
handset other than specified access doors may expose you to dangerous
instructions:
voltages or other risks. Incorrect reassembling can cause electric shock when
the product is subsequently used.
1. Use only the VTech battery supplied, or equivalent.
11. Do not overload wall outlets and extension cords as this can result in the risk of
2. Do not open or mutilate the battery. Released electrolyte is corrosive and
fire or electric shock.
may cause damage to the eyes or skin. It may be toxic if swallowed.
12. Unplug this product from the wall outlet and refer servicing to an authorized
3. Exercise care in handling battery in order not to short the battery with
service facility under the following conditions:
conducting materials such as rings, bracelets, and keys. The battery or
A. When the power supply cord or plug is damaged or frayed.
conductor may overheat and cause burns.
B. If liquid has been spilled into the product.
4. Do not dispose of the battery in a fire. The cell may explode.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the operating
instructions, as improper adjustment of other controls may result in
damage and often requires extensive work by an authorized technician
to restore the product to normal operation.
E. If the product has been dropped and the base and/or handset has been
damaged.
F. If the product exhibits a distinct change in performance.
13. Avoid using a telephone (other than cordless) during an electrical storm. There
is a remote risk of electric shock from lightning.
14. Do not use the telephone to report a gas leak in the vicinity of the leak.
15. Only put the handset of your telephone next to your ear when it is in normal talk
mode.
SAVE THESE INSTRUCTIONS
2
3
Getting Started
Handset Features
REDIAL / PAUSE KEY

You can store pauses into your
speed dial numbers. See Storing
Pauses in Memory
 for details.
CHAN/DELETE KEY

Pressing the CHAN key when
the handset is in use will activate
a channel change to the next
free channel. This is used if you
are experiencing noise or
interference on the current
channel.

When viewing the call log, press
ON/ FLASH KEY
to delete the current record

Press the 
/PHONE key to
displayed.
make a call.

While handset in idle mode,
Setting Up Your 2151

If you are currently on a call, and
press and hold to delete all
1. Choose an area near an electrical outlet and a telephone wall jack.
hear a call waiting tone, press
records in the call log.
2. Plug the AC power adapter into an electrical outlet and the DC connector
FLASH to switch to the second
PROG/SELECT KEY
to the power jack on the bottom of the base unit. Insert the cord in the
call. Press FLASH again to return

Press PROG.
channel guide.
to the original call.
CAUTION: Use only the AC adapter shipped with your 2151. It  is

Press  SELECT  to store a
VOLUME  CONTROL
specifically designed for this product.
directory entry.
NOTE:
Connect power to the base unit before placing the handset in

While on a call, press the   or
the cradle.
 keys to adjust the listening
TONE/ * KEY
3. CHARGE THE HANDSET BATTERY BEFORE USE. The battery
volume. The handset will emit a

In PULSE dialing mode, this key
recharges automatically whenever the handset is in the base unit. The
double beep when the maximum
is used to switch to temporary
battery must be charged for 15 hours before using your phone for the
or minimum volume level has been
TONE dialing mode.
first time.
reached.
PAGE
4. Connect the telephone line cord. Insert one end of the telephone line
VOLUME/CID/PHONEBOOK
Press to page the handset for up
cord into the phone jack on the bottom of  the base unit. Plug the other
KEY
to 60 seconds. Press again, or
end into a telephone wall jack.  Make sure the plugs snap securely into

When phone is not in use, press
press OFF on handset, or place
place. Insert the cord in the channel guide.
(
) to display Caller ID
handset in base to cancel the
5. CHECK FOR A DIAL TONE. After the battery is charged, pick up the
page.
handset and press the ON key. You should hear a dial tone. If not, see
information.
IN CASE OF DIFFICULTY.

When phone is not in use, press
(
) to display directory entries.
OFF KEY

Press the OFF key to end a call
or exit all modes of operation.
4
5


Big size of image:

Please install Flash player from http://get.adobe.com/flashplayer/!

43 43 45 45

Designated trademarks and brands are the property of their respective owners | Disclaimer