RPL450-1 Manuals
PADDED ACTUATOR COVER
PART NO. 1083039
Assembly, Installation and Operating Instructions
NOTE: Check all parts for shipping damage. In case of dam-
INSTALLING/REMOVING THE
age, DO NOT use. Contact your Dealer for further instruction.
ACTUATOR COVER (FIGURE 1)
SAFETY SUMMARY
1. Lock the casters as shown in DETAIL "A".
The following recommendations are made for the safe
2. Remove the metal ring attached to the RED emergency
use of the PADDED ACTUATOR COVER:
release pin as shown in DETAIL "D".
GENERAL WARNINGS
3. Lift-up on the boom and place it on your shoulder.
The Padded Actuator Cover is for use ONLY on
4. Remove the nut, bolt and washer securing the actuator
the following lifts: RPA 450-1, RPL 450-1 and RPA
shaft extension to the boom mounting bracket.
600-1.
DO NOT install or use this equipment without first
5. Remove the pinch guard and bushing from the actuator
reading and understanding these instructions. If
shaft extension.
you are unable to understand the Warnings, Cau-
6. Let the actuator rest on your chest.
tions or Instructions, contact a healthcare profes-
7. Perform one (1) of the following:
sional, dealer or technical personnel before at-
tempting to install this equipment - otherwise, in-
A. Install the actuator cover by sliding the large opening of
jury or damage may occur.
the padded actuator cover over the actuator assembly.
After ANY adjustments, repair or service and
NOTE: Ensure large opening is pulled all the way
BEFORE use, make sure all attaching hardware
down, with elastic band under actuator base. Ensure
is tightened securely - otherwise injury or dam-
RED emergency release pin protrudes through small
age may occur.
hole in actuator cover as shown in DETAIL "B".
INSTALLATION WARNING
B. Remove the actuator cover.
Caster locks MUST be locked during this pro-
8. Rotate the actuator shaft extension until it lines-up with the
cedure to prevent injury or damage.
holes in the boom mounting bracket.
CAUTION
DO NOT tumble dry the actuator cover.
Boom
(STEP 3)
DETAIL "B"
STEP 7
DETAIL "C"
STEPS 4, 5, 8 -11
Actuator
FRONT
BACK
Boom Mounting Bracket
(STEP 6)
Actuator
Pinch Guard
Nut
Cover
Bushing
Actuator
ê
Washers
ê
Base
Bolt
Actuator Shaft Extension
Red Emergency
Release Pin
Step Here
DETAIL "A"
Step Here
DETAIL "D"
to Lock
STEPS 1 AND 13
to Unlock
STEPS 2 AND 12
Metal Ring
Locking
RED Emergency
Lever
Release Pin
FIGURE 1 - INSTALLING/REMOVING THE ACTUATOR COVER
OVER
Big size of image:
Please install Flash player from http://get.adobe.com/flashplayer/!
PART NO. 1083039
Assembly, Installation and Operating Instructions
NOTE: Check all parts for shipping damage. In case of dam-
INSTALLING/REMOVING THE
age, DO NOT use. Contact your Dealer for further instruction.
ACTUATOR COVER (FIGURE 1)
SAFETY SUMMARY
1. Lock the casters as shown in DETAIL "A".
The following recommendations are made for the safe
2. Remove the metal ring attached to the RED emergency
use of the PADDED ACTUATOR COVER:
release pin as shown in DETAIL "D".
GENERAL WARNINGS
3. Lift-up on the boom and place it on your shoulder.
The Padded Actuator Cover is for use ONLY on
4. Remove the nut, bolt and washer securing the actuator
the following lifts: RPA 450-1, RPL 450-1 and RPA
shaft extension to the boom mounting bracket.
600-1.
DO NOT install or use this equipment without first
5. Remove the pinch guard and bushing from the actuator
reading and understanding these instructions. If
shaft extension.
you are unable to understand the Warnings, Cau-
6. Let the actuator rest on your chest.
tions or Instructions, contact a healthcare profes-
7. Perform one (1) of the following:
sional, dealer or technical personnel before at-
tempting to install this equipment - otherwise, in-
A. Install the actuator cover by sliding the large opening of
jury or damage may occur.
the padded actuator cover over the actuator assembly.
After ANY adjustments, repair or service and
NOTE: Ensure large opening is pulled all the way
BEFORE use, make sure all attaching hardware
down, with elastic band under actuator base. Ensure
is tightened securely - otherwise injury or dam-
RED emergency release pin protrudes through small
age may occur.
hole in actuator cover as shown in DETAIL "B".
INSTALLATION WARNING
B. Remove the actuator cover.
Caster locks MUST be locked during this pro-
8. Rotate the actuator shaft extension until it lines-up with the
cedure to prevent injury or damage.
holes in the boom mounting bracket.
CAUTION
DO NOT tumble dry the actuator cover.
Boom
(STEP 3)
DETAIL "B"
STEP 7
DETAIL "C"
STEPS 4, 5, 8 -11
Actuator
FRONT
BACK
Boom Mounting Bracket
(STEP 6)
Actuator
Pinch Guard
Nut
Cover
Bushing
Actuator
ê
Washers
ê
Base
Bolt
Actuator Shaft Extension
Red Emergency
Release Pin
Step Here
DETAIL "A"
Step Here
DETAIL "D"
to Lock
STEPS 1 AND 13
to Unlock
STEPS 2 AND 12
Metal Ring
Locking
RED Emergency
Lever
Release Pin
FIGURE 1 - INSTALLING/REMOVING THE ACTUATOR COVER
OVER
Big size of image:
Please install Flash player from http://get.adobe.com/flashplayer/!