DW101 Manuals


Y
ance enables better control of the tool in unexpected situations.

Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes,
hard hat, or hearing protection must be used for appropriate conditions.

VICIO 
TOOL USE AND CARE

Use clamps or other practical way to secure and support the workpiece to a stable
LÉASE ESTE
platform. Holding the work by hand or against your body is unstable and may lead to loss
O. 
of control.

Do not force tool. Use the correct tool for your application. The correct tool will do the
job better and safer at the rate for which it is designed.


Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled
PRODUCT
with the switch is dangerous and must be repaired.

Disconnect the plug from the power source before making any adjustments, changing
accessories, or storing the tool. 
Such preventative safety measures reduce the risk of starting

ADVERTENCIA: 
the tool accidentally.

Store idle tools out of reach of children and other untrained persons. Tools are dan-
gerous in the hands of untrained users.


Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools,
with sharp cutting edges are less likely to bind and are easier to control.

ANTES DE USAR EL

Check for misalignment or binding of moving parts, breakage of parts, and any other
condition that may affect the tools operation. If damaged, have the tool serviced

DE GARANTÍA. 
before using. Many accidents are caused by poorly maintained tools.

Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool, may become hazardous when used on anoth-
er tool.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SER
PÓLIZA
INSTRUCTIVO 
SERVICE

Tool service must be performed only by qualified repair personnel. Service or mainte-
nance performed by unqualified personnel could result in a risk of injury.


When servicing a tool, use only identical replacement parts. Follow instructions in
the Maintenance section of this manual
. Use of unauthorized parts or failure to follow
Maintenance Instructions may create a risk of electric shock or injury.

Additional Specific Safety Instructions for Drills

Hold tool by insulated gripping surfaces when performing an operation where the
.R.
cutting tools may contact hidden wiring or its own cord. Contact with a “live” wire will
make exposed metal parts of the tool “live” and shock the operator.

po) à régulateur de vitesse et inverseur
.
V


Wear safety goggles or other eye protection. Hammering and drilling operations cause
chips to fly. Flying particles can cause permanent eye damage.

• Keep handles dry, clean, free from oil and grease.  it is recommended to use rubber
gloves.  This will enable better control of the tool.
• Do not overreach while operating the tool. Maintain a balanced working stance at all times.
When necessary, use only properly positioned, safe, platforms and scaffolding. WORK SAFE.

CAUTION:DO NOT TOUCH ANY METAL PARTS OF THE TOOL when drilling or driving into
mm (3/8
walls, floors or wherever live electrical wires may be encountered! Hold the tool only by insulat-
TION
ed grasping surfaces to prevent electric shock if you drill or drive into a live wire.
.S.R. Drill
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other con-
struction activities contains chemicals known to cause cancer, birth defects or other reproduc-
tive harm. Some examples of these chemicals are:

DE INSTRUCCIONES
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and 
• arsenic and chromium from chemically-treated lumber (CCA).

Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals:  work in a well ventilated area, and work with

aladro de 10mm (3/8") V
approved safety equipment, such as those dust masks that are specially designed to filter out
INSTRUCTION MANUAL
GUIDE D'UTILISA
MANUAL
DW100/DW101/DW106
3/8" (10mm)V
Perceuse de 10
de marche
T
microscopic particles.
• The label on your tool may include the following symbols.

V ..........................volts
DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286
Printed in U.S.A. (JUN00-CD-1) Form No. 385907-01    DW100    Copyright © 1998,2000
A ..........................amperes
Hz ........................hertz
W ........................watts
min ......................minutes

........................alternating current
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY DEWALT TOOL,
....................direct current
CALL US TOLL FREE AT:
no ........................no load speed
1-800-4-DEWALT (1-800-433-9258) 
..........................Class II Construction
General Safety Instructions for All Tools
…/min ..................revolutions or reciprocation per minute
WARNING! Read and understand all instructions. Failure to follow all instructions listed
........................earthing terminal
below, may result in electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
........................safety alert symbol
WORK AREA
Motor Brushes

Keep your work area clean and well lit. Cluttered benches and dark areas invite acci-
DEWALT uses an advanced brush system which automatically stops the drill when the brush-
dents.
es wear out. This prevents serious damage to the motor.

Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases, or dust. 
Power tools create sparks which may ignite the dust

Switches
or fumes.
To start drill, depress trigger switch; to stop drill, release trigger. To lock trigger in “ON” posi-

Keep bystanders, children, and visitors away while operating a power tool.
tion for continuous operation, depress trigger and push up locking button “A” Figure 1, then
Distractions can cause you to lose control.
gently release trigger. To release locking mechanism, depress trigger fully, then release it.
ELECTRICAL SAFETY
Before using the tool (each time) be sure that the locking button release mechanism is work-

Double insulated tools are equipped with a polarized plug (one blade is wider than
ing freely.
the other.) This plug will fit in a polarized outlet only one way. If the plug does not fit
Do not lock the switch “ON” when drilling by hand so that you can instantly release the trigger
fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician
switch if the bit binds in the hole.
to install a polarized outlet. Do not change the plug in any way. Double insulation 
The locking button is for use only when the drill is mounted in a drill press stand or otherwise
eliminates the need for the three wire grounded power cord and grounded power supply
held stationary.
system.
Be sure to release the locking button before disconnecting the plug from the power supply.

Avoid body contact with grounded surfaces such as pipes, radiators, ranges and
Failure to do so will cause the tool to start immediately the next time it is plugged in. Damage
refrigerators. There is an increased risk of electric shock if your body is grounded.
or injury could result.

Don’t expose power tools to rain or wet conditions. Water entering a power tool will
THE VARIABLE SPEED TRIGGER SWITCH permits speed control—the farther the trigger is
increase the risk of electric shock.
depressed, the higher the speed of the drill.

Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an
NOTE: Use lower speeds for starting holes without a center punch, drilling in metal or plas-
outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace dam-
tics, driving screws or drilling ceramics. Higher speeds are better for drilling wood and com-
aged cords immediately. Damaged cords increase the risk of electric shock.
position boards, and for using abrasive and polishing accessories.

When operating a power tool outside, use an outdoor extension cord marked “W-A”
THE REVERSING LEVER is used for withdrawing bits from tight holes and removing screws.
or “W.” These cords are rated for outdoor use and reduce the risk of electric shock.
It is located above the trigger switch (B)Figure 2). To reverse the motor, release the trigger
Minimum Gage for Cord Sets
switch FIRST and then push the lever to the right. After any reversing operations, return lever
Volts
Total Length of Cord in Feet
to forward position.
120V
0-25
26-50
51-100
101-150
240V
0-50
51-100
101-200
201-300
Operation
Ampere Rating
More Not 
more 
AWG
DRILLING
Than
Than
1. Always unplug the drill when attaching or changing bits or accessories.
0 -
6
18
16
16
14
2. Use sharp drill bits only. For WOOD, use twist drill bits, spade bits, power auger bits, or
6 -
10
18
16
14
12
hole saws. For METAL, use high speed steel twist drill bits or hole saws. For MASONRY,
10 -
12
16
16
14
12
such as brick, cement, cinder block, etc., use carbide-tipped bits.
12 -
16
14
12
Not Recommended
3. Be sure the material to be drilled is anchored or clamped firmly. If drilling thin material, use
PERSONAL SAFETY
a wood “back-up” block to prevent damage to the material.

Stay alert, watch what you are doing and use common sense when operating a power
4. Always apply pressure in a straight line with the bit. Use enough pressure to keep drill bit-
tool. Do not use tool while tired or under the influence of drugs, alcohol, or medica-
ing, but do not push hard enough to stall the motor or deflect the bit.
tion. A moment of inattention while operating power tools may result in serious personal
5. Hold tool firmly to control the twisting action of the drill.
injury,
6. IF DRILL STALLS, it is usually because it is being overloaded or improperly used.

Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your
RELEASE TRIGGER IMMEDIATELY, remove drill bit from work, and determine cause of
hair, clothing , and gloves away from moving parts. Loose clothes, jewelry, or long hair
stalling.  DO NOT CLICK TRIGGER OFF AND ON IN AN ATTEMPT TO START A
can be caught in moving parts.
STALLED DRILL—THIS CAN DAMAGE THE DRILL.

Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with
7. To minimize stalling or breaking through the material, reduce pressure on drill and ease the
your finger on the switch or plugging in tools that have the switch on invites accidents.
bit through the last fractional part of the hole.

Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that
8. Keep the motor running when pulling the bit back out of a drilled hole. This will help pre-
is left attached to a rotating part of the tool may result in personal injury.
vent jamming.

Do not overreach. Keep proper footing and balance at all times. Proper footing and bal-
9. With variable speed drills there is no need to center punch the point to be drilled. Use a


Big size of image:

Please install Flash player from http://get.adobe.com/flashplayer/!

35 35 49 49

Designated trademarks and brands are the property of their respective owners | Disclaimer