Cadet 3 Flushing System 2384 Manuals


INSTALLATION INSTRUCTIONS
CARE AND MAINTENANCE
CADET® 3 - 1.6 GPF TWO-PIECE TOILET
Models  2383 / 2384 / 2386 / 2447 / 2431 / 2880 / 3305

CADET® 3 FloWise™ - 1.28 GPF TWO-PIECE TOILET
Models  2829 / 2832 / 2835 / 2838 / 2880 / 3305

Thank you  for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is 
installed properly, please read these instructions carefully before you begin. (Certain installations may require professional 
help.) Also be sure your installation conforms to local codes.
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
NOTE: Pictures may not exactly define contour of china and components.
RECOMMENDED TOOLS AND MATERIALS
Putty Knife 
 
Regular Screwdriver  
Adjustable Wrench 
     Sealant 
 
Tape Measure
Hacksaw 
 
Wax Ring/Gasket 
 
Flexible Supply Tube 
     Closet Bolts   
Carpenters Level
1   REMOVE OLD TOILET
a.  Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b.  Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!
c.  Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d.  Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
     NOTE: Mounting surface must be clean and level before new toilet is installed!
2 ROUGHING-IN DIMENSIONS:
NOTE: Distance from wall to closet flange centerline must be as listed on chart:
MODELS
DIMENSION “A”
2383.010   2384.010
254mm (10)
FINISHED WALL
10"
2386.010  
ROUGHS
2383.012 2829.128
2386.012 2832.128
2384.012 2835.128
12"
305mm (12)
3305.000 2838.128
SUPPLY
ROUGHS
2431.012
AS
REQ'D.
2447.000 2447.128
2880.000 2880.128
FINISHED 
2383.014   2384.014
356mm (14)
FLOOR
14"
2386.014 
ROUGHS
A
3
4
5
SAVE FOR FUTURE USE
WAX RING
CLOSET
SEALANT
NUT
FLANGE
TAPERED
WASHER
A
CLOSET 
BOLTS
CLOSET
BOLT
 FLANGE
INSTALL WAX SEAL
INSTALL CLOSET BOLTS
Invert toilet on floor (cushion to prevent 
POSITION TOILET ON FLANGE
Install closet bolts in flange 
damage), and install wax ring evenly 
a.  Unplug floor waste opening and install toilet on closet flange       
channel, turn 90°, and slide 
around waste flange (horn), with tapered 
     so bolts project through mounting holes.
into place 6" (152mm) apart 
end of ring facing toilet. Apply a thin bead 
b.  Loosely install retainer washers and nuts. Side of washers    
and parallel to wall.
of sealant around toilet base.
     marked "THIS SIDE UP" must face up!
P r o d u c t   n a m e s   l i s t e d   h e r e i n   a r e   t r a d e m a r k s   o f   A S   A m e r i c a ,   I n c .
7 3 0 9 2 8 - 1 0 0   R e v .   F
©   A S   A m e r i c a ,   I n c .   2 0 0 8


Big size of image:

Please install Flash player from http://get.adobe.com/flashplayer/!

35 35 51 51

Designated trademarks and brands are the property of their respective owners | Disclaimer