91044 Manuals


Figure 3
Figura 3
Note: Blue Wire is for 3-Pin Installations
Remarque : le fil bleu sert aux installations à trois broches
Importante: El cable azul se utiliza en instalaciones de 3 clavijas
Easy Lock Light Base
Waterproof Butt-Joint Connectors
Connecteurs par raccordement en about imperméables
91041-91044 (2-Wire), 91045-91048 (3-Wire)
Conectores con juntas impermeables en los extremos
SAVE THESE INSTRUCTIONS
Switch
Form Number 69423  Rev. A  
08-05
Interrupteur
Fuse Must Match Light Specs
Interruptor
Les fusibles doivent correspondre 
FEATURES
aux spécifications de la lumière
This base is designed for use with Attwood All-Round Lights and Attwood Pole-Mounted Combination 
El fusible debe respetar 
Sidelights. The base includes a locking spring that holds the pole tightly in place.
las especificaciones 
Blue
CAUTION:
de iluminación
(pos)
(neg)
Bleu
For 12-volt D.C. only.
(pos)
(nég)
Azul
Always disconnect the power source when installing or servicing this product. Always remove 
(positivo) (negativo)
Gray
the boat from the water before using 120V AC power tools.
Gris
REQUIRED FOR INSTALLATION 
Figure 1
• Cordless drill
Figura 1
• 1/16" bit, 1" and 7/8" hole saws or bits
12V DC
Black
•  4 #10 stainless steel pan head screws suitable 
12 Volts CC
Noir
  for the deck material (do not use fl at head screws)
12 voltios de CC
Negro
• Waterproof crimp connectors for 16-gauge wire
• Fuse-holder and fuse (amperage depends on light used)
OPERATION
• 2- or 3- Position switch (depending on lights used)
NOTE: This base accepts many non-Attwood light poles. However, the locking function does not 
LOCATION
operate with other manufacturers’ poles. 
Figure 1 is a simplifi ed drawing showing placement of navigation 
NOTE: Attwood Locking Collar stays above the Easy Lock Base 
lights in relationship to one another. 
1. Align pole screw with locking spring. Insert pole into base (Figure 4).
1. For Pole-Mounted Combination Sidelights:  Position the light 
2. Press down fi rmly to engage electrical connectors. Be sure locking spring clicks over pole screw. 
base at the bow and on the centerline of the boat.
3. On poles with Attwood Locking Collar do not try to insert collar into base; allow collar to remain 
2. For All-Round Lights:  Position light base at the stern, on the 
above base. 
starboard side.
4. To remove pole:
INSTALLATION
  • Pull locking spring back
  • Pull pole straight up.
1. At the selected location, mark position for a pilot hole at exact center of the light base. (See Figure 2)
5. Close cover to protect contacts when not in use.
2. Before drilling, MAKE SURE that:
  • Mounting surface is fl at
TO CONVERT POLE FOR USE WITHOUT LOCKING COLLAR
  • You will not drill into wires, hoses, or other obstructions
1. Remove screw at bottom of pole. Slide locking collar off end of pole.
  • Area is large enough to fi t base (1-1/2" W x 3-3/8" L,  38mm x 86mm).
2. Replace screw in the upper screw hole.
3. Drill pilot holes at both center marks. Drill clearance holes as shown below. (Figure 2)
4. Remove burrs from around the hole. On aluminum boats, be certain wires can not contact hull. 
Figure 4
Feed wires and base socket into hole in deck. 
Figura 4
5. For Bow Light, align base with boat centerline and place hinge toward bow. Using base as 
template, mark position of mounting screws.
NOTE: If area below the base will not be reachable after installation, attach suitable lengths of 
16-gauge color-matched NON-POWERED wire that can be routed to an accessible area. Make 
connections according to WIRING INSTRUCTIONS (Figure 3).
6. Remove base and drill for mounting screws. 
Locking Spring
7. Gasket provided must be used instead of caulk under base to prevent locking feature 
Ressort de verrouillage
malfunction. Reinsert base, and fasten with four #10 stainless steel screws 
Resorte de seguridad
(not provided). DO NOT OVERTIGHTEN screws.
WIRING INSTRUCTIONS
CAUTION:
 
Failure to make proper connections and fuse the light base properly will void the product warranty.
Polarity is important. If wiring is mis-connected, LED-illuminated lights will not operate.
All positive wires must be fused according to light specifi cations to protect the circuit. MAKE 
SURE POWER SOURCE IS 12-VOLT D.C. ONLY. HIGHER VOLTAGE CAN CAUSE DAMAGE TO LIGHT 
AND WIRE CIRCUITRY.

1. Navigation rules require sidelights to be operated separately from anchor lights. Use either two 
This product carries the standard Attwood one year warranty. See Product Catalog or 
switches or a single switch with three positions for off / anchor / navigation (Figure 3).
attwoodmarine.com for details.
2. For all wiring connections, use crimp-type marine-grade connectors with suitable waterproof 
insulation. Protect all connections with suitable materials. (Figure 3)
  (2 wire base): 
  • Connect the (-) black wire to the negative (-) wire from the 12-volt supply. 
• Connect the (+) gray wire to a fused and switched positive (+) 12-volt supply. 
(3 wire base): 
  • Connect the (-) black wire to the negative (-) wire from the 12-volt supply.
• Connect the (+) gray wire to a fused switch (+) for the navigation light. 
© 2008 Attwood Corporation
• Connect the (+) blue wire to a fused positive (+) wire from the 12-volt supply. 
1016 N. Monroe Street, Lowell, MI 49331-0260   www.attwoodmarine.com  
Figure 2
.72"
.72"
Figura 2
1,828 cm
1,828 cm
0,72" (18,2 mm)
0,72” (18,2 mm)
1.06" Dia. Hole
Trou de 2,69 cm de diamètre
1" Dia. Hole
Agujero de 1,06" (26,9 mm) de diámetro
Trou de 2,54 cm de diamètre

Agujero de 1" (25,4 mm) de diámetro

1.97"
1.97"
5,003 cm
5,003 cm
.625"
1,97" (50.0 mm)
1,58 cm

1"
1,97" (50.0 mm)
0,625" (15,8 mm) 
2,54 cm
1" (25,4 mm) 
.76"
1.93 cm
.875 Dia. Hole
0,76" (19,3 mm)
Trou de 2,22 cm de diamètre
Agujero de 0,875" (22,2 mm) de diámetro


(4) Pilot Hole Locations
(4) Pilot Hole Locations
Emplacements des trous de guidage (4)
Emplacements des trous de guidage (4)
.72"
.72"
(4) Ubicaciones para los agujeros guía
(4) Ubicaciones para los agujeros guía
1,828 cm
1,828 cm
0,72" (18,2 mm)
0,72" (18,2 mm)


Big size of image:

Please install Flash player from http://get.adobe.com/flashplayer/!

39 39 47 47

Designated trademarks and brands are the property of their respective owners | Disclaimer