9083 Manuals


2. Loosen the two screws in the clamping bracket, then place it over
the windshield frame and mirror base at the selected location.
(Figure 2)

OPTION 1
For windshield frames less than .450" thick, or a
stepped frame (Figure 3), a small spacer of aluminum,
plastic, or marine plywood may be used between the
Ski Mirror
base and the windshield frame.
9083
OPTION 2
For windshields with a stepped frame (Figure 3),
Installation Instructions
using the mounting bracket as a template, mark the
SAVE THESE INSTRUCTIONS
width of the bracket on the windshield frame step.
Form Number 69212T  Rev. B
03-10
Using a file, remove the step from this area.
FEATURES
Figure 2
Windshield Frame
The Attwood Ski Mirror is designed with a universal mount which
allows mounting on either the dash or windshield extrusion (up to
3/4" thick). It adjusts freely to any position, any angle, up or down
or side to side.
The design includes a shatterproof convex lens that eliminates blind
spots. It is compact and lightweight.
Tighten
The spring-loaded ball joint holds mirror firm to prevent vibrating out
Screw
of position.
Adjust
Also features gleaming ZAMAK with Perma-Plate® chrome finish.
Figure 3
DASH-MOUNTED SKI MIRROR
Step
Step
Tools and Materials Required for Installation
1. Drill and drill bits.
2. Two #10 x 3/4" stainless steel wood/sheet metal pan-head screws
3. Tighten two clamping bracket screws.
(not included).
CAUTION:  Overtightening the screws could cause damage to the
3. Phillips Head screwdriver.
threads, clamping bracket, windshield/windshield frame.
INSTALLATION INSTRUCTIONS
4. After mirror is mounted, adjust to desired position. If mirror cannot
1. Select a desirable location at or near centerline of the boat, making
be adjusted sufficiently, rotate the mirror head one-half turn. (The
sure there is enough room to work before drilling. (Figure 1)
mirror may need to be removed to do so.)
NOTE:  Mirror head tension does not require adjustment; a
Figure 1
permanent tension system is built in and preset by Attwood.
Adjust
Tighten
ATTWOOD LIMITED WARRANTY
Screws
Attwood Corporation, 1016 North Monroe, Lowell, Michigan 49331 (“Attwood”) warrants
to the original consumer purchaser that Attwood brand products will be free from defects
in materials and workmanship under normal use and service for one year from the date
of original consumer purchases.
This limited warranty is not applicable if the product has been damaged by accident,
Center of Dash
improper installation, unreasonable or improper use, lack of proper maintenance,
unauthorized repairs or modifications, normal wear and tear, or other causes not
arising out of defects in materials or workmanship.
Attwood products are warranted for use on pleasure boats. Any other use – including
but not limited to commercial, racing, or non-marine use – are not covered under this
warranty. Attwood’s obligation under this warranty is limited to repair of the product at
2. Mark the hole locations using the base as a template.
Attwood’s plant or replacement of the products at Attwood’s option without expense to
3. Drill two suitable sized holes.
the original consumer purchaser. Any expenses involved in the removal, reinstallation
4. With mirror in place, use two #10 screws and fasten to dash.
or transportation of the product are not covered by this warranty. The product must be
returned to Attwood’s plant at the address above, postage pre-paid, and insured with
5. After mirror is mounted, adjust to desired position. If mirror cannot
proof of original purchase including date. If Attwood is unable to replace the product and
be adjusted sufficiently, rotate the mirror head one-half turn.
repair is not commercially practical or cannot be timely made, or if the original consumer
(The mirror may need to be removed from the dash to do so.)
purchaser is willing to accept a refund in lieu of repair or replacement, Attwood may
refund the purchase price, less an amount for depreciation. The acceptance by Attwood
NOTE:  Mirror head tension does not require adjustment; a
of any product returned or any refund provided by Attwood shall not be deemed an
permanent tension system is built in and preset by Attwood.
admission that the product is defective or in violation of any warranty. Products that
are replaced or for which a refund is issued become the property of Attwood.
WINDSHIELD-MOUNTED SKI MIRROR
THIS WARRANTY IS ATTWOOD’S ONLY EXPRESSED WARRANTY OF THESE
PRODUCTS. NO IMPLIED WARRANTY INCLUDING, WITHOUT LIMITATION, THE
NOTE:  Windshield installation is not recommended for frameless
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, SHALL BE EXTENDED BEYOND THE WARRANTY PERIOD STATED
windshields.
ABOVE FOR EACH PRODUCT. ATTWOOD SHALL NOT BE LIABLE FOR ANY
DAMAGES, FOR LOSS OF USE OF THIS PRODUCT, NOR FOR ANY OTHER
Tools and Materials Required for Installation
INCIDENTAL OR CONSEQUENTIAL DAMAGES, COSTS, OR EXPENSES.
1. Phillips Head screwdriver.
Some states do not allow limitations or how long an implied warranty lasts or the exclusion
2. Optional metal cutting file.
or limitation of incidental or consequential damages, so the above limitations and exclusions
3. Optional aluminum, plastic, plywood spacer.
may not apply to you. This warranty gives you specific legal rights, and you may have
other rights which vary from state to state.
INSTALLATION INSTRUCTIONS
1. Select a desirable location at or near centerline of the windshield.
© 2003 Attwood Corporation
1016 N. Monroe Street, Lowell, MI 49331-0260   www.attwoodmarine.com


Big size of image:

Please install Flash player from http://get.adobe.com/flashplayer/!

36 36 47 47

Designated trademarks and brands are the property of their respective owners | Disclaimer