410-R Manuals


Style 410-R
Thank you for purchasing a Shakespeare antenna product. 
Supplied Parts
Customer comments are welcome. Before installing, please study 
1  Swivel Mount assembly
the diagram and check parts supplied against those listed.
1  Standoff Bracket assembly
IMPORTANT! Please read all instructions              
before installing.
1  1“ Reducing adapter
The Style 410-R Mounting Kit is a versatile antenna mounting 
1  11/8“ Reducing Adapter
kit comprised of a Shakespeare Style 81-S Swivel Mount and a 
Shakespeare Style 408-R Standoff Bracket. The dual swivel mount 
Retainer Bar
permits mounting on vertical or horizontal surfaces. For use with 
STANDOFF 
Wing Nut
1½” antennas, and antennas of 11/
Reducing Adapter
8” and 1” diameter by using the 
BRACKET
appropriate adapter (supplied) in the standoff bracket.
Antenna
Standoff Bracket 
Tools required:  Drill and drill bit for ¼” screws; 
Assembly
screwdriver; wrench or pliers
Installation Instructions
Mounting 
Choose an antenna mounting location that is as high as feasible, 
Screw*
as free as possible from obstructions, and as far as possible from 
other antennas and strong sources of RF.
1.  Using the base of the Swivel Mount as a template, mark the 
location for the four mounting holes. Drill ¼” holes.
     Note: When drilling fiberglass, place a wooden backup block 
behind the surface if possible, to minimize push-through 
damage.
Washer*
2.  Attach the Swivel Mount to the mounting surface using 
Nut*
Lockwasher*
hardware (sold separately) that is applicable to the mounting 
surface.
Nut*
SWIVEL 
Mounting Screw*
IMPORTANT:  If the thickness of the mounting 
MOUNT
surface is not adequate to support the antenna under 
Lockwasher*
expected stress, a wooden back-up pad (not supplied) 
1”-14 Thread
should be applied underneath the mounting surface 
during installation.
Mount Base
3.  Assemble the antenna to the Swivel Mount, being careful not to 
damage the antenna’s cabling, if any.
4.  Loosen the wing nut on top of the Standoff Bracket and slide 
the retainer bar out of the way. Gently place the antenna in its 
mounting position in the U-shaped opening in the bracket.  For 
11/8” and 1” antennas, put the appropriate reducing adapter 
(supplied) in the opening.
5. Rotate the retainer bar over the antenna to lock it in place.
6. Using the Standoff Bracket itself as a template, mark the position 
for its mounting holes.
7. Drill ¼” mounting holes, and install the bracket using stainless 
steel hardware appropriate to the mounting surface (hardware 
sold separately).
8. Tighten the wing nut to secure the antenna in the bracket. The 
3
completed installation should attach the antenna firmly to the 
Swivel
5
-
mounting surface, leaving no “play” between the antenna and 
9
0
the standoff bracket.
-
1
* Not supplied. For some types of mounting surfaces you might need 
1
27
stainless steel woodscrews or other hardware.
-
0
0
Shakespeare Electronic Products Group
U.S. Operations: 6111 Shakespeare Rd. · Columbia, SC 29223 · 803-227-1590 · Fax: 803-419-3099 · www.shakespeare-marine.com
U.K. Operations: Enterprise Way, Fleetwood, Lancashire, FY7 8RY, England · +44 (0) 1253 858787 · Fax: +44 (0) 1253-859595 · www.vtronix-antennas.com
Shakespeare is a subsidiary of Jarden Corporation (NYSE: JAH)
©2002 Shakespeare Co.        ·  Form I-410-R  J: rev. 04/25/2010


Big size of image:

Please install Flash player from http://get.adobe.com/flashplayer/!

40 40 51 51

Designated trademarks and brands are the property of their respective owners | Disclaimer